Gemini CD Player CD 9500 Pro III User Manual

GEMINI  
CD-9500 PRO III  
Professional  
Dual  
CD  
Player  
OPERATIONS MANUAL  
 
Pushing the POWER SWITCH (1) a second time will turn the unit off.  
INTRODUCTION  
DISC TRAY: The DISC TRAY (2) is where the CD is held during loading,  
unloading and playback. Pressing the disc tray OPEN/CLOSE  
BUTTON (3), will open or close the tray. The DISC TRAY (2) holds  
both 12 cm and 8 cm CDs. Please note, if the CD-9500 PRO III is in  
the play mode, the tray will not open.  
Congratulations on purchasing a Gemini CD-9500 PRO III Dual CD Player.  
This state of the art professional CD player is backed by a three year  
warranty, excluding lasers. One year warranty on CD lasers. Prior to  
use, we suggest that you carefully read all the instructions.  
OPEN/CLOSE BUTTON: Press the OPEN/CLOSE BUTTON (3) to load  
or remove a CD from the DISC TRAY (2).  
CAUTIONS  
DISPLAY: The DISPLAY (4) shows the track number, play mode, pause  
mode, and 3 different time displays. These time displays are time  
elapsed on the track, time remaining on the disc and time remaining  
on the track.  
Do not use this CD Player at temperatures below 41°F/5°C or higher  
than 95°F/35°C.  
Place the unit in a clean and dry location.  
Do not place the unit in an unstable location.  
PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (5) causes  
the operation to change from play to pause or from pause back to  
play. See the CUE INSTRUCTIONS section for more information.  
When disconnecting the power cord from an AC outlet, always grasp it  
by the plug. Never pull the power cord.  
To prevent electric shock, do not remove the cover or the bottom  
screws. There are no user serviceable parts inside. Please refer  
servicing to a qualified technician.  
TRACK SKIP: The TRACK SKIP BUTTONS (6) let you select the track  
to play.  
SEARCH BUTTONS: The SEARCH BUTTONS (7) are used to  
accurately position the disc at the point where you wish the track to  
start playing. This position on the track is memorized as the cue  
point. Each push of the SEARCH BUTTONS (7) will put the unit into  
pause mode and move the memorized cue point 1 frame (1/75th  
second). See the CUE INSTRUCTIONS section for more information.  
Do not use chemical solvents to clean the unit.  
Keep the laser pickup clean by keeping the drawer closed.  
Keep this manual in a safe place for future reference.  
SAFETY CERTIFICATIONS  
SEARCH DIAL: Use the SEARCH DIAL (8) to select the scanning  
direction and speed. Turning the dial in the clockwise direction will  
scan forward and counter clockwise will scan in reverse. The  
scanning speed increases as the dial is turned further. The SEARCH  
DIAL (8) will not change the cue point and will not bring the unit to  
the pause mode.  
Laser Diode Properties  
Material: Ga - Al - As  
Wavelength: 755 - 815 nm (25° C)  
Laser Output: Continuous Wave, max. 0.5mW  
STOP: The STOP BUTTON (9) will end the playing of the CD.  
IMPORTANT NOTE  
TIME: The TIME BUTTON (10) switches the time display between the  
three available choices listed under DISPLAY.  
Since the CD-9500 PRO III is a dual CD player, most of the functions and  
controls are duplicated on both sides of the CD player. To eliminate  
confusion and to make the drawings easier to understand, we will only  
number the right side functions and controls. The only controls that are  
not duplicated are the POWER SWITCH (1) and the VOLTAGE SELEC-  
TOR SLIDE SWITCH (17).  
CUE: With the unit in the play mode (play/pause LED glows green), and  
after using the SEARCH BUTTONS (7) to memorize the cue point,  
pressing the CUE BUTTON (11) will cause the CD player to enter the  
pause mode (play/pause LED blinks green) at the memorized cue  
point (the cue LED glows yellow). If the cue point was not memo-  
rized, the unit will return to the beginning of the track. Holding down  
the cue button changes the cue function to preview (allowing you to  
hear the music play at whatever tempo you adjusted to by holding  
the cue button down). Releasing the cue button returns you to the  
preset cue point.  
LINE VOLTAGE SELECTION  
Model CD-9500 PRO III is a dual voltage unit. It will operate at 115 or 230  
volts. The unit is preset at the factory to 115 volts. To set the proper  
voltage follow these steps:  
CUE/B REPEAT: After the cue point is memorized, pressing the CUE/B  
BUTTON (12) in the play mode, (the cue LED BLINKS yellow),  
repeats the section between the cue point and the point where the  
CUE/B BUTTON (12) was pressed (there will be a slight delay  
between the end and the restart of play).  
1. Place the head of a screw driver in the center of the VOLTAGE  
SELECTOR SLIDE SWITCH (17) found on the rear panel.  
2. Slide the switch left for 115 volts or push the switch right for 230  
volts.  
SINGLE: Pressing the SINGLE (15) button will activate single mode and  
the AUTO CUE FUNCTION which causes the unit to play one track  
at a time and to stop at the beginning of music of the following track.  
This allows you to start play immediately from the start of music  
without any blank space (which exists at the beginning of every  
track).  
3. Do not force or twist the switch. Excessive force may cause  
damage. If the switch does not move smoothly, contact a qualified  
technician.  
CONNECTIONS  
1. Using the included cables, plug one end into the REMOTE JACK (20)  
on side 2 and the other end into the PLAYER JACK (19) also on side  
2. Do the same for side 1.  
CONTINUE: The CONTINUE (16) function will cause the unit to play  
continuously (after the last track, the unit will return to the first track  
of the disc and continue to play).  
2. Plug one end of a set of RCA connectors into each of the LINE  
OUTPUT JACKS (18).  
PITCH: Pushing the PITCH BUTTON (13) activates the pitch section of  
the unit (pitch LED glows red). The pitch of the CD will change  
according to the position of the PITCH CONTROL (13). Pushing the  
PITCH BEND BUTTONS (14) will temporarily raise or lower the pitch  
without changing the slide setting. Releasing the buttons will return  
the pitch to the slide setting. Maximum pitch deviation is +/- 8 %.  
3. Plug the other end of the RCA connectors into any available line level  
input jacks on your mixer. If you are playing the CD-9500 PRO III  
through a receiver, you can plug the RCA connectors into the CD or  
AUX input jacks on your receiver. If there are no CD or AUX inputs,  
use any line level (not phono) inputs.  
DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD  
DRIVE, or other such items which accept digital signals to the BNC  
OUTPUT CONNECTOR (21) on the rear panel of the transports  
allows you to record a digital signal from CD.  
FUNCTION DESCRIPTIONS  
POWER SWITCH: After making sure that the VOLTAGE SELECTOR  
SLIDE SWITCH (17), found on the rear panel, is properly set, plug  
the unit in and press the POWER SWITCH (1). The unit will turn on.  
Page 2  
 
and will skip on most or all CD players. Before sending the unit in for  
repair, try playing a CD that you are sure plays properly.  
OPERATING INSTRUCTIONS  
1. Make sure that the VOLTAGE SELECTOR SLIDE SWITCH (15),  
found on the rear panel, is set for the proper voltage. Plug the unit in  
and press the POWER SWITCH (1). The unit will turn on. Pushing the  
POWER SWITCH (1) a second time will turn the unit off.  
SPECIFICATIONS  
GENERAL:  
2. Press the OPEN/CLOSE BUTTON (3), place a CD in the DISC TRAY  
(2) and press the OPEN/CLOSE BUTTON (3) again. The tray will  
close into the unit. The display will initially show the number of tracks  
and the total time of the CD and the unit will be in the pause mode  
(play/pause LED blinks green). When the display shows track  
number 1 and time of 00:00, the unit is ready to use.  
Type.................... Dual Mechanism Compact Disc Player w/wired remote  
Disc Type............................... Standard Compact discs (12 cm & 8 cm)  
Time Display.....................Track Elapsed, Track Remain, or Total remain  
Variable Pitch...........................+/- 8% Slider with Resume Switch  
Pitch Bend...........................................................+/- 8% Maximum  
Instant Start....................................................Within 0.03 seconds  
Track Selection....................................................1 to 99 Tracks  
3. Push the TRACK SKIP BUTTONS (6) to select the track you want to  
play.  
4. Press the PLAY/PAUSE BUTTON (5) and the unit will instantly play.  
Installation...............................19" Rack Mountable Player Unit, 2 U  
19" Rack Mountable Control Unit, 2 U  
AUDIO SECTION:  
CUE INSTRUCTIONS  
To start the play at a point other than the beginning of a track, follow  
these instructions.  
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser  
Oversampling Rate..................................................................8 Times  
Sampling Frequency......................................................44.1 kHz  
Frequency Response....................................20 Hz to 20 kHz  
Digital Output....................................................................IEC958  
Total Harmonic Distortion......................................Less Than 0.05%  
Signal to Noise Ratio...................................................104 dB  
Dynamic Range.................................................................98 dB  
Channel Separation.......................................................90 dB (1 KHz)  
Output Level.............................................................1.9 Volts R.M.S.  
Power Supply......................................AC 120/230V, 50/60 Hz  
1. To memorize the approximate spot at which you want play to start,  
select the proper track, and then push the PLAY/PAUSE BUTTON  
(5) so the unit goes into the play mode (play/pause LED will glow  
green). Listen to the CD and when the CD gets to the approximate  
spot, push either of the SEARCH BUTTONS (7). The unit will go into  
the pause mode (play/pause LED will blink green) and the location  
indicated on the display will be the memorized cue point.  
2. To fine tune the memorized cue point, push the PLAY/PAUSE  
BUTTON (5) so the unit goes into the play mode (play/pause LED  
glows green) and listen carefully to the starting point. Push the CUE  
BUTTON (11) and the unit will enter the pause mode (play/pause  
LED blinks green) and the CD will reposition at the previously  
memorized cue point. If you decide that this point is okay, leave the  
unit alone until you are ready to play it. At that time push the PLAY/  
PAUSE BUTTON (5). The unit will instantly play from the spot  
selected. If the selected spot is not where you want it, with the unit  
in the play mode, simply push the CUE BUTTON (11). The unit will go  
back to the previously selected spot, and enter the pause mode. By  
pressing either the left or right SEARCH BUTTONS (7) you can hear  
and move the cue point forward or backward. After you have  
located the spot, play the CD and listen to the start. If it’s still no  
good, push the CUE BUTTON (11) and try again. The memorized cue  
point will always be the last location after using the SEARCH  
BUTTONS (7).  
Dimensions...............................Player Unit 19' (W) x 3 1/2" (H) x 10" (D)  
Control Unit 19' (W) x 3 1/2" (H) x 3 5/8" (D)  
Weight...........................................................Player Unit 11.7 lbs (5.3 kg)  
Control Unit 3.8 lbs (1.7 kg)  
TROUBLE SHOOTING  
If the disk will not play, check to see if the disc was loaded correctly  
(label side up). Also check the disc for excessive dirt, scratches,  
etc.  
If the disc turns but there is no sound, check the cable connections.  
If they are okay, check your amplifier or receiver.  
If the CD skips, check the CD for dirt or scratches. Do not assume  
that the CD player is defective. Many CDs are recorded out of spec  
Parts of the design of this product may be protected by worldwide patents. Information in this manual is subject to change without notice and does not represent  
a commitment on the part of the vendor. Gemini Sound Products Corp. shall not be liable for any loss or damage whatsoever arising from the use of information  
or any error contained in this manual.  
No part of this manual may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, electrical, mechanical, optical,  
chemical, including photocopying and recording, for any purpose without the express written permission of Gemini Sound Products Corp..  
It is recommended that all maintenance and service on the product should be carried out by Gemini Sound Products Corp. or it’s authorized agents. Gemini Sound  
Products Corp. cannot accept any liability whatsoever for any loss or damage caused by service, maintenance or repair by unauthorized personnel.  
Worldwide Headquarters • 8 Germak Drive, Carteret, NJ 07008 • USA • Tel (732) 969-9000 • Fax (732) 969-9090  
© Gemini Sound Products Corp. 1998 All Rights Reserved  
 

Eureka Air Compressor PBL SMC 10 NR User Manual
Euro Pro Carpet Cleaner EP63CH User Manual
Exakta Digital Camera EXA IIa User Manual
Excalibur electronic Games ET454 User Manual
Extron electronic Switch FOX T USW 203 User Manual
FieldServer Computer Drive FS 8700 130 User Manual
GE Cooktop JBP83 User Manual
GE Dishwasher 165D4700P382 User Manual
GE Freezer FCM 7 User Manual
Gitzo Camcorder Accessories GT 530 User Manual