EverFocus Camcorder 520TVL 380TVL User Manual

1/3” 520TVL High-Res. Color Camera(350HQ/550)  
1/3” 380TVL High-Res. Color Camera(250)  
 
Table of Contents  
Safety Warning ……...……………………………………3  
Introduction……………………………………………….4  
Specification……………………………………………….5  
Major Parts and Their Functions………………….…….6  
Installation Instructions……………………………..…. 11  
ii  
 
Safety Warning  
1. Handle camera with care.  
Be careful when handling the camera, do not drop it or subject it  
to strong shock or vibration to prevent any damages to it. Do not  
disassemble it or place it on an unstable base.  
2. Do not install camera near electric or magnetic fields.  
Install the camera away from any television, radio transmitter,  
magnet, electric motor, transformer, or audio speakers since the  
magnetic fields generated from the above named devices will  
distort the video image.  
3. Do not install camera in a high temperature environment.  
Install the camera away from space heaters, stoves, or other heat  
generating devices because the high temperatures generated  
around these devices can cause deformation, discoloration or  
other damages to the camera. Install the camera in an area where  
the temperature range remains between 0o to 50 o C (32o to 122o  
F).  
4. Never aim camera toward the sun whether the unit is in use or  
not.  
The severe rays of direct sunlight or objects that emit extremely  
intense rays may cause fatal damage to the sensor and internal  
circuit.  
5. Cleaning  
Do not touch the surface of the CCD sensor directly. Use a soft  
cloth to remove any dirt from the camera body. Use a lens  
tissue or cotton tipped applicator and ethanol to clean the CCD  
sensor and/or the camera lens. Always replace the cover cap on  
the lens mount, when the camera is not in use.  
3
 
Introduction  
The new 350 HQ series is a solid-state color video camera  
specifically designed for high quality surveillance applications. It  
incorporates break through DSP technology that provides the most  
reliable and accurate color picture in the security industry. The  
camera is convenient to use with C-mount or CS-mount lenses and  
an easy back-focus adjustment helps efficient installation.  
Main Features:  
1/3” color CCD pickup device for more than 380/520 TV lines of  
horizontal resolution.  
Sophisticated DSP (Digital Signal Processing) circuitry design that  
delivers excellent picture quality and performance.  
Wide range automatic electronic shutter: up to 1/100,000.  
Auto line lock with external phase adjustment.  
Use with either C-mount or CS-mount lenses and easy back-focus  
adjustment  
System available in NTSC or PAL.  
4
 
Specifications  
Model  
250  
350HQ  
550EX  
Pickup Device:  
Video Format:  
1/3” interline transfer color CCD  
NTSC / PAL  
NTSC: 510(H) x 492(V) NTSC: 768(H) x 494(V)  
PAL: 500(H) x 580(V) PAL: 752(H) x 582(V)  
Picture Element:  
Horizontal  
Resolution:  
380TV lines  
0.5lux/F=1.2  
520TV lines  
0.5lux/F=1.2  
1.0lux color, 0.15lux  
monochrome/F=1.2  
Sensitivity:  
Video Output:  
S/N Ration:  
BNC VBS 1.0Vp-p, 75ohm  
Over 48dB  
Electronic  
Shutter:  
Up to 1/100,000  
Back Light  
comp.:  
ON/OFF switch  
Auto Gain  
Control:  
ON/OFF switch  
Auto White  
Balance:  
Digital auto tracing  
ON/OFF switch  
Fluorescent:  
Auto IRIS:  
Switch-able Video Drive or Direct Drive  
1. Line-Locked with LL on  
2. Internal Sync. With LL off  
Sync. Mode:  
Gamma  
Correction:  
>0.45  
Power Source:  
Dimension  
12VDC/24VAC; 90~265VAC  
51(W) x 57(H) x 140.2(D)mm;2(W)x 2.25(H)x5.52(D)inch  
Operating  
Temperature:  
Power  
0°~50°,20%~80%  
5W max.  
Consumption:  
5
 
Major Parts Names and Their Functions  
1
3
Front  
Side  
7
Top  
12(optional)  
Rear (EQ series) Rear(EQ series” A”)  
6
 
1. Focal Length Adjustment Ring  
Use this ring to adjust the appropriate focal length according to  
the lens type. Rotate the ring clockwise for a CS-mount lens;  
rotate the ring counterclockwise for a C-mount lens. The  
factory setting is C-mount.  
2. Lens Mount  
Used to mount an appropriate C-mount or CS-mount lens.  
3. Locking Screw  
Use the locking screw to set the focal length.  
4. Lens Connector (4 pin socket)  
Connect to the lens plug of the auto iris lens.  
5. Control Switches  
There are six (6) control switches located on the sideboard.  
These are used to set the special features. The switches in order  
are for Flicker less, Back Light Compensation, Electronic  
Shutter, Automatic Gain Control, Line-Lock and Auto Iris Lens  
type.  
Fluorescent On/OFF  
This is a function compensates for the flickering images that can  
occur in fluorescent light conditions. When filming images in  
fluorescent lighting, turn on the Fluorescent function; the default  
setting is off.  
BLC (Back Light Compensation) On/Normal  
When BLC is turned on, the AGC, ES and IRIS operating point is  
determined by averaging over the center area instead of entire field-  
of-view, so that a dimly-lit foreground object in the center area can  
be clearly distinguished from brightly-lit backgrounds. BLC should  
not be used unless it is needed to compensate for back-lighting.  
The default setting is Normal.  
7
 
ES (Electronic Shutter) Off/On  
ES ON: The camera continuously adjusts the shutter speed from 1/60  
(NTSC),1/50 (PAL) second to 1/100,000 second according to the  
luminance conditions of the scene.  
ES OFF: The shutter speed is fixed at 1/60 (NTSC), 1/50 (PAL)  
second. Place ES in the off position, when auto iris lens are used or  
flicker is observed under extremely bright fluorescent lighting. In all  
other lighting, keep ES in the on position for optimum performance.  
The default setting is ON.  
AGC (Automatic Gain Control) Off/On  
AGC ON: The sensitivity increases automatically when light is low.  
AGC OFF: A low-noise picture is obtained under a low light  
condition. The default setting is ON.  
LL (Line-Lock) Off/On  
Use this switch to select the sync mode between Internal Sync.(LL  
off) and Line-Lock (LL on). To synchronize the camera to the  
internal time base, set the line-lock in the off position. By setting the  
line-lock on, the camera’s vertical synchronization can be driven by  
the AC signal in the power lines.  
Note: The cameras feature AC line lock for external  
synchronization. Using the AC power frequency (60Hz) is  
possible but not available when using DC or other  
operation power such as NTSC in 50Hz or PAL in 60Hz  
power system.  
8
 
VD/DD (Auto Iris lens Type)  
For video drive auto iris lens, please set the switch to VD. For direct  
drive iris lens, set the switch to DD. The default setting is DD. Wire  
the lens cable to the lens connector according to the following table.  
Pin1 Pin2 Pin3 Pin4  
Lens Connector  
Video Drive +12V GND VD-IRIS GND  
Direct Drive Cnt-Cnt+ Drv+ Drv-  
2
1
6. IRIS Level Control  
Brightness Level can be adjusted from the IRIS level VR while  
using the direct drive lens.  
2• Turn counterclockwise to L for a darker picture.  
1• Turn clockwise to H for a brighter picture.  
7. V-Phase Adjustment Screw  
The vertical phase may require adjustment to synchronize the  
vertical phase of the camera with other camera in the system when  
it is to be used in the line-lock sync mode. Make the adjustment  
when the vertical phase of the camera does not match with other  
cameras.  
8. Mounting Base and Fixing Screws  
To use when the mounting bracket is required while mounting the  
camera. The mounting base can be attached to either the top or the  
bottom of the camera; fix the mounting base onto the camera by  
using the 4 supplied fixing screws.  
9
 
9. Video Output Connector  
BNC VBS 1.0 Vp-p, 75ohm  
1 Power Cable (EQ series)  
2 DC12V/AC24V Screw Terminals (EQ series “A”)  
3 Audio Output(optional):Connect with an audio device, RCA  
connector  
10  
 
Installation Instructions  
1) Remove the cap cover from the top of the lens mount.  
2) To attach a C-mount/CS-mount lens, turn the focal length  
adjustment ring to the appropriate position. Note: If a C-mount  
lens is used, please make sure the focal length adjustment ring  
is set at C position before fixing the lens.  
a) Screw the lens firmly onto the lens mount. Insert the lens plug  
in the lens connector if the auto iris lens is used.  
b) Tighten the locking screw.  
c) Connect the video output of the camera to a color monitor or  
other video device through a 75 ohm type coaxial cable with  
BNC female connector.  
d) Plug the power cord to the outlet.  
e) Once the image appears on the monitor, adjust the focus and  
diaphragm of the lens to obtain the best picture.  
f) If the subject is not in focus when adjusting focus of lens, do  
focal length adjustment as following:  
i) Loosen the locking screw of the focal length adjustment ring.  
ii) Take picture of subject at a distance more than 20m away  
from the camera.  
iii) Rotate the focal length adjustment ring to bring the subject  
in focus.  
iv)Tighten the locking screw while the adjustment is completed.  
11  
 
EverFocus Electronics Corporation  
Home Office:  
12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-  
USA Office:  
2445 Huntington Drive, San Marino, CA 91108, U.S.A. TEL: +1-626-844-8888  
European Office:  
Albert-Einstein-Strasse 1 D-46446 Emmerich, Germany TEL: 49-2822-9394-0  
China Office:  
Room 609, Technology Trade Building, Shandgdi Information Industry Base,  
Haidian District, Beijing,China TEL: +86-10-62971096 FAX: +86-10-62971432  
Japan Office:  
1809 WBG MARIBU East 18F, 2-6 Nakase.Mihama-ku. Chiba city 261-7118, Japan  
P/N: MQ35G00900  
12  
 
13  
 

Dyson Vacuum Cleaner 1741801 User Manual
Echo Trimmer SRM 3800 TYPE1 E User Manual
Essick Air Humidifier EP9 500 User Manual
Festool Router OF 1400 EQ User Manual
Fiesta Gas Grill ESD45055 B401 User Manual
Fisher Price Baby Gym J0220 User Manual
Flymo Lawn Mower EM032 User Manual
Fujitsu Refrigerator 990TX2 User Manual
Furuno Network Router IB 681 User Manual
Genesis Advanced Technologies Speaker GENESIS 53 User Manual